Need Help understanding how to install new subwoofer and amp to 2022 Lariat with B and O

[Glendawg619]

Hello, I recently purchased these items

Sub box and Amp Combo : https://www.amazon.com/KICKER-48CDF124-Subwoofer-Enclosure-Amplifier/dp/B096YDYDKW

LC2I converter combo : https://www.amazon.com/AccuBASS-2-C...-1-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9hdGY&psc=1



I am aware that I will have to run 8 gauge power and ground to the battery in the frunk, but the rest is a bit confusing to me. Does the stock B and O amp already have low or high level input going into the amp that i would be able to steal to feed the new amp? or will i need to still splice into a speaker wire? Is there any other hardware that im missing to complete the job? any help would be greatly appreciated

Sponsored

 

[Andrewbens]

I would call sound good but purchasing this would help you out a lot.
https://soundsgoodstereo.com/produc...-t-harness-compatible-with-2021-ford-vehicles

 

[daczone]

Hello, I recently purchased these items

Sub box and Amp Combo : https://www.amazon.com/KICKER-48CDF124-Subwoofer-Enclosure-Amplifier/dp/B096YDYDKW

LC2I converter combo : https://www.amazon.com/AccuBASS-2-Ch-Line-Out-Converter/dp/B0CGRZJGCH/ref=sr_1_1_sspa?crid=2UWN3TT62L6PU&dib=eyJ2IjoiMSJ9.xLzVPpo0TwJn47DGPEiB1VekB3IF0LT_15Gm-x90ISvFB45RZ49TKp8BYgQL4VQteztBfBKVeY_hPxVJ3fikcZAN3vQLs1KiAa4FFAXk_JfRNAP8rxFXKF9JehNpqp-w8-eemlEKnTO9F05aZkjs6q5lza3Sa9XbsIw4eKUwSYAd0L98knwC8LJJnenwOqzRE_ZCFB0yRMuE-1UOn8PiB8g8xfApBTHSw622ShHzRVK669-O4msIZeKH4Ifp9cxqJPCjYMTdv4ovkPEADlKrSQJscO691Nm6kV-wgVJJtpw.2y6R0GvCUJGfi186lkc-4ONE7i3P0gFrgkmnVzvlW6k&dib_tag=se&keywords=lc2&qid=1732668273&s=electronics&sprefix=lc2,electronics,195&sr=1-1-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9hdGY&psc=1



I am aware that I will have to run 8 gauge power and ground to the battery in the frunk, but the rest is a bit confusing to me. Does the stock B and O amp already have low or high level input going into the amp that i would be able to steal to feed the new amp? or will i need to still splice into a speaker wire? Is there any other hardware that im missing to complete the job? any help would be greatly appreciated

If you haven't done this yet:

Add a Subwoofer to your B&O Lightning

You basically have 2 options. Grab the existing signal going to the factory subwoofer. Which will need to go through some sort of line converter (I used the Kicker KEYLOC). Or intercept the signal before the Amp with a harness (Shown in the link above) which still would need a line converter. The difference is bypassing the factory bass cutoff that the B&O system adds/removes to the signal.

Sponsored