ECU module programming guide using FDRS

[Jesse-Infotainment]

What I am saying is DO NOT load all from an old back up.. You can make changes but dont load all

Sponsored

 

[Ajzride]

Did you pull the USB stick out first? Or did you mean the update no longer appears in the SW tab?

It no longer appears in the software tab, the only thing I have is the GSM procedure. The update failed, but it still cleared itself out and I can't get back in.

 

[JEB]

Are you referencing changing the

@Bob_Mac yes I made changes for adaptive headlights to the two below

720-01-01. 22FOA 3064 F4EA

720-10-01. 0B18 0061 00BC

Are you referencing changing the

@Bob_Mac yes I made changes for adaptive headlights to the two below

720-01-01. 22FOA 3064 F4EA

720-10-01. 0B18 0061 00BC

Slow down. Do a network scan. Are you getting DTCs? You need to check this FIRST!

 

[Bob_Mac]

Are you referencing changing the

@Bob_Mac yes I made changes for adaptive headlights to the two below

720-01-01. 22FOA 3064 F4EA

720-10-01. 0B18 0061 00BC

Can you change the values back to what the originals ones were? If you don't have them then try this as last resort.

720-01-01 2F0A 1064 F4CA

 

[Skier167]

Slow down. Do a network scan. Are you getting DTCs? You need to check this FIRST!

@JEB sorry, yes I did a network scan and the module came back green with no DTC’s also the IPC update is still present. All modules are green and no dtc’s present on any module now.

 

[Bob_Mac]

What I am saying is DO NOT load all from an old back up.. You can make changes but dont load all

I hope no one is doing that...

 

[JEB]

@JEB sorry, yes I did a network scan and the module came back green with no DTC’s also the IPC update is still present. All modules are green and no dtc’s present on any module now.

Can you run the IPC from scratch now? Erase the flash drive and start again as if you’d never touched the IPC before.

The IPC is a weird animal. I had made FORSCan changes previously and I was still able to update. But if the standard method doesn’t work, you have work to do. You’ll probably need to have @Bob_Mac walk you through restoring the original configuration and then a CAN bus update. But try the original method first.

 

[Jesse-Infotainment]

I hope no one is doing that...

Well When I saw it mentioned someone had a structure mismatch that is why.. So I just wanted to make it clear not to

 

[Bob_Mac]

@JEB sorry, yes I did a network scan and the module came back green with no DTC’s also the IPC update is still present. All modules are green and no dtc’s present on any module now.

Please look at what I posted... your FORScan changes could be affecting the update. The last line stays only the first one I posted gets changed. The last 2 of the last block will get recalculated if it's wrong.

 

[Bob_Mac]

Well When I saw it mentioned someone had a structure mismatch that is why.. So I just wanted to make it clear not to

Right there with you... I had them do only a single change...

 

[Bob_Mac]

It no longer appears in the software tab, the only thing I have is the GSM procedure. The update failed, but it still cleared itself out and I can't get back in.

Did you make ANY changes to the IPC using FORScan?

 

[El Amigo]

IPMA errors

 

[Bob_Mac]

IPMA errors

That does NOT pertain to their issue. The IPMA has been cleared back a few posts ago. Don't need people doing these things if it's not necessary!

 

[Ajzride]

Did you make ANY changes to the IPC using FORScan?

Not that I remember. Let me look back through my changes.

EDIT:

I didn't think about these being in the IPC, but I guess they are.

Disable driver & passenger seatbelt minder	IPC	720-01-01	xxxx	xx0x	xx--
Disable Auto Engine Idle Shutdown of 30 mins	IPC	720-01-01	x*xx	xxxx	xx--	subtract 8 from your default value (if default is F, change to 7)

So I suppose I need to go manually fix those two and then try the PMI again?

 

[Bob_Mac]

No

Let me ask it another way... have you done any FORScan changes?

Sponsored